Cover Kitchen Remodeling Nationwide

Cover Kitchen Remodeling: The Mountain View Owner’s Guide

Cover kitchen remodeling in Mountain View typically runs $14,000-$45,000 for a full renovation, with smaller refreshes starting around $9,000. We stock Cover-compatible cabinetry, hardware, and finishing systems, and we quote every job with a flat written price before any demolition starts. Most Cover kitchen projects we handle in Mountain View move from signed contract to permit in under two weeks.

Call (669) 215-4852

Homeowners usually call us after noticing cabinet doors that won’t stay aligned, drawer glides grinding instead of sliding, or water damage where the sink cabinet meets the floor. These aren’t cosmetic annoyances; they’re signs that the original install is reaching end of life, often 15-20 years in the Peninsula’s dry-then-humid climate cycle.

Which Cover Models This Applies To

Cover manufactured kitchen systems across several product lines from the late 1990s through the mid-2010s, and the hardware specs vary significantly by era. The pre-2005 units used 35mm cup hinges with a 110-degree opening angle and a specific 5/8-inch overlay; post-2005 Cover shifted to soft-close Blum-style hinges with a different bore pattern. If you’re trying to match hardware, check the inside face of the cabinet box for a stamped date code and a model prefix - “CV-” indicates the Classic Value line, “CS-” the Custom Select line, and “PR-” the Pro Series that was sold primarily through regional distributors in Northern California.

We don’t source from Cover directly; Rowan Construction Group Mountain View is an independent service provider with no affiliation to the manufacturer. For hardware replacement, we typically specify quality aftermarket equivalents from Blum or Salice that match the original mounting pattern but offer better long-term availability. The one compatibility gotcha we’ve learned: Cover’s Pro Series used a proprietary 40mm hinge cup spacing that doesn’t map cleanly to standard European hardware, so we measure on site before ordering. For full cabinet replacement, we quote from our vetted brand list - KraftMaid and Wellborn for painted or stained wood, with Cambria or Silestone for the countertop surface.

Signs Your Cover Kitchen Remodeling Is Failing

• Doors hang crooked or won’t close flush. This usually means the hinge cups have wallowed out in the particleboard substrate, or the original 35mm screws have stripped their holes. In Mountain View’s older Eichler and ranch-style homes, we’ve found this accelerates where kitchen humidity spikes near the range with no vented hood.
• Drawer boxes sag or bind in the opening. The roller or undermount glide has lost its nylon bearings, or the drawer box itself has delaminated at the dovetail. Cover’s Classic Value line used a side-mount roller system with a 75-pound rating; load it with cast-iron and it fails in eight to ten years.
• Water staining or swelling at the sink base. The sink cabinet floor is 3/4-inch particleboard with a laminate skin; once moisture breaches the edge banding, it expands like a sponge. We see this most in homes near the Stevens Creek corridor where the water table runs high and slab moisture wicks upward.
• Laminate surfaces peeling at the edges or bubbling at the seams. Heat damage from an unvented toaster oven or steam from a kettle degrades the contact adhesive. Cover’s post-form laminate can’t be field-repaired; replacement is the only fix that holds.
• Wall cabinets pulling away from the stud line. The original installer may have hit drywall only, or used inadequate fasteners for the load. In Mountain View’s seismic zone, this is a genuine safety issue - a loaded wall cabinet can weigh 200-plus pounds.

Before

After

Replacement Cost & What’s Included

What drives the range: square footage, whether we’re moving plumbing or gas lines, and material selection. A 10×10 kitchen with KraftMaid semi-custom cabinets, Cambria quartz, and no layout change sits near the lower third of the full-remodel band. Add a load-bearing wall removal, structural engineering, and permit expediting for Mountain View’s planning department, and you’re looking at the upper range. Under Clause 1 of the Haven Standard, the price we write is the price you pay - no change order gets signed without your initials, and we’ve kept projects within a few percent of the agreed number across 4,000-plus jobs since 2007.

DIY or Call Us?

There’s a short list of things a homeowner can safely assess: measuring cabinet openings, photographing hinge bore patterns, and checking for obvious water damage with a flashlight and a moisture meter. What’s not safe is removing wall cabinets solo - the weight distribution is unpredictable, and a stripped or missed stud means the box comes down with you under it. We’ve also seen homeowners cut into walls looking for plumbing without checking for live electrical in the same stud bay; Mountain View’s older homes often have ungrounded Romex run diagonally between fixtures.

Our crew carries the proper jacks, temporary supports, and electrical testers. Every visit includes a documented photo record - standard, not an upgrade - so you see what we found and what we did. If you want a second opinion on another contractor’s quote, bring it by and we’ll review it line by line at no charge. Call (669) 215-4852 to schedule your free estimate.

FAQs